Service note for JA-110R Radio Module This product is a component of the JABLOTRON JA-100 alarm system. It enables wireless communication with wireless Jablotron 100 series components. Because of the extension of the coverage area, up to three JA-110R modules can be used in the system. The product is intended...
JA-110R (0)
Too much choice? Chat or call us at 085-0160316
There are no products in these categories. Shop on.
Service note for JA-110R
Radio Module
This product is a component of the JABLOTRON JA-100 alarm system. It enables wireless communication with wireless Jablotron 100 series components. Because of the extension of the coverage area, up to three JA-110R modules can be used in the system. The product is intended to be installed by a trained technician with a valid Jablotron certificate.
Installation
The module can either be installed directly in the cover of the control unit cabinet, or it can be placed in a suitable location in the house. Do not place the module near larger metal objects, also not near installations or pipes that may adversely affect wireless communication.
Figure:1 - snap clip of the screen; 2 - yellow signal light of interference; 3 - red signal light of communication
1. Open the screen (by pressing the snap clip 1).
2. If the module is installed in the cover of the central unit, screw on the plastic back panel as shown.
Figure: installation of the module in the cover of the central unit.
3. If installed on a wall in the house, prepare the supply of the BUS cable and mount the back panel at the chosen location (a vertical orientation is recommended).
Before connecting the BUS, the system must be disconnected from the power supply.
4. Connect the BUS cable to the terminals (the cable must not enter the antenna area when the screen is closed). If the module is installed in the cover of the central unit, connect the BUS via a cable through to the connectors.
The flat cable with RJ connectors may only be used for connecting the BUS up to a maximum length of 3 m.
5. Continue to follow the installation instructions of the control unit. Basic steps:
a. After switching on, the yellow signal light (2) flashes because the module has not been read into the system.
b. In the F-Link programme, select the required position on the peripherals card and start the learning mode with the Read-in button.
c. Press the tamper switch in the module (6) - causing the module to learn and the yellow light will extinguish.
6. Close the cover of the module.
Figure: 4 - antenna; 5 - serial number; 6 - sabotage switch; 7 - terminals of the BUS; 8 - connector of the BUS; 9 - cable with connectors (installation in the cover of the control unit);
Setting module properties
This is done by the F-Link programme - peripheral devices card. On the position of the module use Internal setting. A dialogue appears, where the following properties can be set:
LED indication at communication: from the factory it is set that at operation the module indicates communication with a wireless peripheral with the red signal light. You can turn this indication off.
Fault detection: from the factory is off. However, it can be set to two levels - low (interference lasts longer than 30s over the course of a minute) and high (interference lasts longer than 10s for 20s). If detection is enabled, the system is able to report communication band interference.
Learning signal: by using this selection in the programme, the module sends a learning signal (intended for wireless peripherals, which contain only one receiver).
Technical parameters
Power supply from the BUS of the central unit 12 V (9...15 V)
Current consumption in standby (idle) 25 mA
Current consumption for cable selection 25 mA
Radiocommunication 868,1 MHz
Dimensions 150 x 40 x 23 mm
Classification grade 2
compliant with CSN EN 50131-1, CSN EN 50131-3, CSN EN 50131-5-3
Environment compliant with CSN EN 50131-1 II. indoor, general
Range of operating temperatures -10 to +40°C
Further complies with CSN ETSI EN 300220, CSN EN 50130-4,
CSN EN 55022, CSN EN 60950-1
Conditions of operation CTÚ VO-R/10/06.2009-9
Product is designed and manufactured in accordance with the provisions to be applied thereto: Government Decree No 426/2000 Sb., if used according to its intended use.
Note: Although this product does not contain harmful materials, do not dispose of it in the domestic waste, but dispose of it at the collection point intended for electronic waste.
Installation
The module can either be installed directly in the cover of the control unit cabinet, or it can be placed in a suitable location in the house. Do not place the module near larger metal objects, also not near installations or pipes that may adversely affect wireless communication.
Figure:1 - snap clip of the screen; 2 - yellow signal light of interference; 3 - red signal light of communication
1. Open the screen (by pressing the snap clip 1).
2. If the module is installed in the cover of the central unit, screw on the plastic back panel as shown.
Figure: installation of the module in the cover of the central unit.
3. If installed on a wall in the house, prepare the supply of the BUS cable and mount the back panel at the chosen location (a vertical orientation is recommended).
Before connecting the BUS, the system must be disconnected from the power supply.
4. Connect the BUS cable to the terminals (the cable must not enter the antenna area when the screen is closed). If the module is installed in the cover of the central unit, connect the BUS via a cable through to the connectors.
The flat cable with RJ connectors may only be used for connecting the BUS up to a maximum length of 3 m.
5. Continue to follow the installation instructions of the control unit. Basic steps:
a. After switching on, the yellow signal light (2) flashes because the module has not been read into the system.
b. In the F-Link programme, select the required position on the peripherals card and start the learning mode with the Read-in button.
c. Press the tamper switch in the module (6) - causing the module to learn and the yellow light will extinguish.
6. Close the cover of the module.
Figure: 4 - antenna; 5 - serial number; 6 - sabotage switch; 7 - terminals of the BUS; 8 - connector of the BUS; 9 - cable with connectors (installation in the cover of the control unit);
Setting module properties
This is done by the F-Link programme - peripheral devices card. On the position of the module use Internal setting. A dialogue appears, where the following properties can be set:
LED indication at communication: from the factory it is set that at operation the module indicates communication with a wireless peripheral with the red signal light. You can turn this indication off.
Fault detection: from the factory is off. However, it can be set to two levels - low (interference lasts longer than 30s over the course of a minute) and high (interference lasts longer than 10s for 20s). If detection is enabled, the system is able to report communication band interference.
Learning signal: by using this selection in the programme, the module sends a learning signal (intended for wireless peripherals, which contain only one receiver).
Technical parameters
Power supply from the BUS of the central unit 12 V (9...15 V)
Current consumption in standby (idle) 25 mA
Current consumption for cable selection 25 mA
Radiocommunication 868,1 MHz
Dimensions 150 x 40 x 23 mm
Classification grade 2
compliant with CSN EN 50131-1, CSN EN 50131-3, CSN EN 50131-5-3
Environment compliant with CSN EN 50131-1 II. indoor, general
Range of operating temperatures -10 to +40°C
Further complies with CSN ETSI EN 300220, CSN EN 50130-4,
CSN EN 55022, CSN EN 60950-1
Conditions of operation CTÚ VO-R/10/06.2009-9
Product is designed and manufactured in accordance with the provisions to be applied thereto: Government Decree No 426/2000 Sb., if used according to its intended use.
Note: Although this product does not contain harmful materials, do not dispose of it in the domestic waste, but dispose of it at the collection point intended for electronic waste.